How To Paint Fascia Board After Installing New One Under Drip Edge

Download Article

Download Article

Fascia boards are institute around the edges of your roof and usually support your home's rain gutter system. Over time, these boards may start to rot or need to exist replaced due to impairment. Luckily, replacing a fascia board is as easy as taking out the old lath and plumbing equipment a new one in its place. Once you've installed a new lath, all you demand to do is seal the seams and paint it to match your abode. With a curt afternoon renovation, you lot can accept new fascia boards that will last for years!

1. i

   Uninstall the gutter system from the fascia board you're replacing. Unscrew the gutters from backside your existing fascia board with an electric screwdriver. And then, locate the brackets underneath your gutter belongings them in place and unscrew them so y'all can elevator the gutter upwardly and away from the fascia. Remove the gutter brackets from your fascia so yous can reuse them on the new board.^[1]

   • Work with a partner and so y'all don't impairment your gutters when y'all remove them.
   • If your fascia board doesn't take any gutters, you may skip this step.

2. 2

   Cut the board into three ft (0.91 m) sections with a reciprocating saw. Marker out 3 ft (0.91 m) sections along your fascia board with a pencil. Make vertical cuts into the fascia lath between your roof rafters. Cut out each 3 ft (0.91 thou) section one at a time until yous've removed the full lath.^[ii]

   • This step is not required, only it makes it easier to remove the board in pieces.

   Advertisement

3. 3

   Pound the boards off of the rafters from behind with a hammer. Go along the fascia board steady with your nondominant hand. Hold a hammer with your dominant mitt behind your existing fascia boards and start pounding it to loosen the nails. Continue hitting the board until the nails behind information technology come out from the rafters. Once the board is loose, pull it off from your habitation.^[iii]

   • If the fascia lath is rotting, endeavour to pause off equally much of the rotting forest as possible before sawing through the boards.

   Tip: Make sure there's a rafter at the terminate of your fascia board then you lot take a place to spike information technology.

4. 4

   Saw through whatever nails going into your roof with a blade meant for metallic-cutting. Some boards are continued from the top through the roof as well as the rafters. Put a bract meant for cutting metal onto your reciprocating saw and cut along the top seam of the board so you have a flat surface for your new board.^[4]

   • Don't pound the blast back into the roof since it may impairment the shingles in a higher place it.

   Advertizement

1. 1

   Measure the length of your roof where you're installing your fascia board. Use a record measure to discover how long your roof is where yous're putting in the new fascia. Make sure to double check your measurements then your cuts are precise.^[five]

2. ii

   Cutting the lath to the length you need with a round saw. Use a board made for outdoor apply and so it doesn't develop any rot, such as outdoor-treated spruce, pine, or cedar. Set the board on saw horses or a sturdy work surface so the cease y'all're cutting hangs over the edge. Turn on your round saw and cut through the forest.^[6]

   • Wear safety glasses as you work with a circular saw so your eyes are protected.

3. 3

   Miter the end of your board to make a clean seam with another. Mitered corners hide seams by cutting the ends of your boards to 45-degree angles. Ready the angle on your round saw to a 45-degree angle and trim the finish of your board.^[7]

   • Yous tin also hire a miter saw if you want to make more than precise cuts, but a circular saw will work if it'south all you have.
   • Miter cuts merely need to exist made if yous're putting your fascia on a corner.

   Advertisement

1. one

   Mark the locations of your rafters on the drip edge above the fascia. Fascia boards need to exist secured to the rafters in social club to stay in place. Apply a pencil to marker the locations of the rafter boards so you lot know where to place your nails later on on.^[8]

   • Drip edges are metal flashing pieces forth the border of your roof to help water period abroad from your fascia.
   • If you don't have a drip edge, mark the measurements on the edge of your roof or on the fascia board itself.

   Tip: Rafters are usually spaced 12 in (30 cm), sixteen in (41 cm), or eighteen in (46 cm) apart on center. If you aren't able to make marks, use the measurement between your rafters as a guide.

2. two

   Use 1-ii nails through each rafter to secure your fascia board. Hold the lath in place, and use two in (five.1 cm) nails and a hammer to secure it in identify. Identify your nails in line with the marks on your baste edge and place information technology in the center of your fascia lath. Drive ane-2 nails in per rafter so information technology doesn't motion effectually. Make certain each cease of your fascia board is nailed into a rafter and so they don't bow out or intermission your seal.^[ix]

   • Have a partner help you agree the board in place while you nail it and so it's kept straight.

3. 3

   Cover all of the seams with body filler. Utilise a bonding body filler putty then water can't go in between the seams and damage the wood. Mix the filler with a putty pocketknife on a flat sail of cardboard or on a plate and scrape it onto your fascia board. Go over the seam 2-3 times so the putty gets pushed into it. Then, encompass all of your nails with the putty equally well. Look for 1 day for your putty to completely prepare.^[10]

   • Body filler can be purchased from your local hardware store.
   • Merely mix a small corporeality of the body filler at a time since it dries quickly.

4. 4

   Paint the new fascia board if y'all desire it to match the rest of your home. Once the fascia board is sealed, paint one-2 coats of outdoor primer onto the wood and let it dry for vi hours. When the primer is dry and evenly coats the surface, use a layer of outdoor paint to help protect your wood and blend it into the rest of your home. Allow the first layer of paint dry completely before applying another coat.^[11]

   • Use any leftover pigment you may have from the last time your house was painted.

   Advertizing

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Cheers for submitting a tip for review!

• Never step on the pigment shelf on top of your ladder.

• Always maintain 3 points of contact while you climb your ladder.

• Clothing centre protection while working with saws and ability tools.

Advertisement

Things You'll Need

• Ladder
• Electric screwdriver
• Safe spectacles
• Reciprocating saw
• Hammer
• Circular or miter saw
• 2 in (5.1 cm) nails
• Body filler putty
• Putty pocketknife
• Outdoor primer
• Outdoor paint
• Paintbrush
• Foam roller

About This Article

Thanks to all authors for creating a page that has been read 94,968 times.

Did this article help y'all?

Source: https://www.wikihow.com/Replace-a-Fascia-Board

Posted by: bakerbrion1976.blogspot.com

Share this post